INCLINE PLATFORM LIFT
Photo Gallery
|
Incline Platform Lift Resources
|
The ES 125 is built with reliability and safety in mind. Its anti-skid surface, grab rails, obstruction sensor and safety brake make it a sound choice for both residential and commercial use.
|
Standard Equipment
|
-
Aluminum extruded rail
-
Continuous pressure buttons
-
Mechanical access ramps
-
One deflector sheave
-
Cable driven unit
-
Safety underpanel sensor
-
2 grab rails on car
-
Keyed call/send controls on platform and at each landing
-
Safety Brake
-
Wall mounted call / send controls
-
Obstruction sensors
-
ABS plastic carriage covers
-
Textured anti-slip surface on platform and ramps
-
Car folds within 11" (279mm) of wall
|
Optional Equipment
|
-
3-position manual safety armrests
-
Motorized 2 position safety armrests
-
Fold-down seats with safety belt
-
Powered fold platform
-
Touch sensitive plate on the access ramps and under the platform to stop the lift if an obstruction is encountered
-
12 volt battery operation
-
Hand-held pendant control on the platform
-
Split rail
-
Drive cabinet at top landing
-
Audio visual alarm
-
Motor with electro-mechanical brake
-
Emergency stop switch
-
Custom color
-
Post for call/send station
-
Outdoor package
-
Zero clearance at top landing to avoid landing door
(Not available on Plus model)
-
Fire service function
-
Pre drilled guide rail for masonry walls
-
Joined guide rail for ease of access on narrow sites
-
Self-support posts
-
Manual lowering device
-
Three (3) sided access to platform with motorized lateral access ramp
-
Flush cabinet at front or back of rail (Plus system)
-
Self-support posts
|
Specifications
|
- Platform Dimensions:
- Type I: 27.50" x 36" (700 x 914 mm)
- Type II: 28.50" x 44" (724 x 1,118mm)
- Type III: 30" x 48" (762 x 1,219 mm)
- Type IV: 30" x 44" (762 x 1,118 mm
- All platforms have non-skid surfaces. The platform can be folded manually or with the help of an optional power-fold platform. Once folded the unit uses very little space in order to leave the staircase virtually unobstructed.
- Access Ramps - Two positive action automatic access ramps for straight or 90° entry
- Motor Assembly - 110 VAC, ½ hp (373 W), 1,750 rpm / gear reducer: 50:1
- Type of Drive Unit:
- Standard system : Aircraft cable 3/16" (5 mm) with breaking load of 4,200 lbs (1,950 kg), deviator pulley and winding drum in a machine room.
- Plus system: Roller chain #50 and aircraft cable with breaking load of 6,100 lbs (2,767 kg). The electric motor gear reducer and controller are self enclosed at the top landing in a drive cabinet. No machine room required.
- Controller - Meets CSA and ETL standards - 24 VAC operating controls
- Power Supply - 110 VAC, 1Ph, 60Hz, 15 amp
- Rated Speed - 14.0 ft / min. (0.071 m / s)(approx.)
- Capacity - One person in a wheelchair
- Rated Load - 450 lbs (240 kg)
- Operating Controls - Continuous pressure directional buttons are installed on the platform with a key switch for increased safety. (*)
- Call Stations - Continuous pressure directional buttons are installed at each landing
- Finish - One coat of primer and two coats of beige acrylic urethane paint on all steel surfaces.
- Safety Features - Automatic dual access ramps, mechanical emergency brake in case of drive system failure, slack cable switch, keyed continuous pressure controls and upper / lower limit switches are standard features on this unit
- Backed by the Savaria Concord Limited Warranty wich covers the repair or replacement of any defective parts for a period of 36 months from date of shipment
|
|
|
|
|
|